Jonsered FC2145W Manuel d'utilisateur

English FC2145 FC2145S BC2145 FC2145W CC2145 Operator ′ s manual Please read the oper ator’s manual carefully and make sure you understand the i

GENERAL SAFETY PRECAUTIONS10 – Englishbe checked. See instructions under the heading Maintenance.Stop switchUse the stop switch to switch off the engi

GENERAL SAFETY PRECAUTIONSEnglish – 11saw. Certain harnesses also have a quick release fitted to the support hook.Check that the harness straps are cor

GENERAL SAFETY PRECAUTIONS12 – Englishoperate the socket spanner when loosening or tightening the nut.The nylon lining inside the locking nut must not

GENERAL SAFETY PRECAUTIONSEnglish – 13Keep the correct setting on the saw blade! Follow our instructions and use the recommended setting tool. An inco

GENERAL SAFETY PRECAUTIONS14 – EnglishTrimmer head• Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufactur

ASSEMBLYEnglish – 15Assembling the handlebar and throttle (BC 2145, CC 2145)• Remove the screw at the rear of the throttle handle.• Slide the throttle

ASSEMBLY16 – Englishmachine is in a comfortable working position when it hangs from the harness.Transport position, handlebar• The handlebar can easil

ASSEMBLYEnglish – 17• Centre the metal cup (P) on the drive disc’s blade guide.• Turn the output shaft until one of the holes in the drive disk aligns

ASSEMBLY18 – Englishspanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socke

ASSEMBLYEnglish – 19• Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.• To dismantle, follow the i

KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

ASSEMBLY20 – EnglishAdjusting the harness1 Tighten the hip strap so that it sits securely.2 Tighten the chest strap under your left arm so that it fits

FUEL HANDLINGEnglish – 21Fuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat

FUEL HANDLING22 – EnglishMixing• Always mix the petrol and oil in a clean container intended for fuel.• Always start by filling half the amount of the

STARTING AND STOPPINGEnglish – 23Check before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent

STARTING AND STOPPING24 – EnglishWarm engineUse the same starting procedure as for a cold engine but without setting the choke control in the choke po

WORKING TECHNIQUESEnglish – 25General working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

WORKING TECHNIQUES26 – English• Control the felling direction (take advantage of the wind).Working methods• Before you start clearing, check the clear

WORKING TECHNIQUESEnglish – 27• To fell to the left, the bottom of the tree should be pushed to the right. Tilt the blade and bring it diagonally down

WORKING TECHNIQUES28 – EnglishGrass clearing using a grass blade• Grass blades and grass cutters must not be used on woody stems.• A grass blade is us

MAINTENANCEEnglish – 29CarburettorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The eng

CONTENTS English – 3 Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Long-term exposure to noise can re

MAINTENANCE30 – EnglishLow speed jet LTry to find the highest idle speed by turning the low speed jet L clockwise then anti-clockwise. When the highest

MAINTENANCEEnglish – 31Correctly adjusted carburettorWhen the carburettor is correctly adjusted the machine will accelerate without hesitation and bur

MAINTENANCE32 – EnglishClean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system result

MAINTENANCEEnglish – 33Spark plugThe spark plug condition is influenced by:• Incorrect carburettor adjustment.• An incorrect fuel mixture (too much or

34 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 35TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/

36 – EnglishTECHNICAL DATANote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC.Note 2:

English – 37TECHNICAL DATABC 2145Approved accessories Type Cutting attachment guard, Art. no.Centre hole in blades/cutters, Ø 25,4 mm Output shaft thr

38 – EnglishTECHNICAL DATA EC-declaration of conformity (Applies to Europe only)We, Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, decl

1Poly Trim2345678<20mm>20mm!BA6 NmX 10

4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to buy a Jonsered product!We are convinced that you will appreciate with

12345678935-50 NM~ 15 cm6'"Clic"~ 3,5 m11 '7,0 m23'2,4-3,3 mm.095"-.130"12 cm5"Trimmy SII

2,7-3,3 mm.106-.130"15 cm 6"15 cm 6"15 cm 6"15 cm 6"12356710111.)2.)>1,1 Kw<1,1 Kw2,7 mm - 9,0 m3,0 mm

"Clic"123567910 m32'484,3 m14'2,7-3,3 mm.106-.13"10 cm 4"6"15 cmTap n’Go 45 Spin

1151200-26´®z+S4"¶6c¨´®z+S4"¶6c¨2008-05-22

English – 5 WHA T IS WHA T? What is what on the c learing saw? (BC 2145)26272863517422243393287182019214131212934342324113025131214161523353610 1

6 – English WHA T IS WHA T? What is what on the c learing saw? (FC 2145, FC 2145 S, FC 2145 W)2427252623635131112971781416152122181420181928293023

English – 7 WHA T IS WHA T? What is what on the c learing saw? (CC 2145)12326272835422243393287182019214131212934342324113025131214161523353461017

GENERAL SAFETY PRECA UTIONS 8 – English Impor tant Personal protective equipment HELMET A helmet should be w orn if the trees being cleared are tal

GENERAL SAFETY PRECA UTIONS English – 9BOOTSWear boots with steel toe-caps and non-slip sole.CLOTHINGWear clothes made of a strong fabric and avoi