Jonsered FC 2145S Manuel d'utilisateur

FC2145 FC2145S BC2145 FC2145W CC2145 Oper ator’s manual (EPA) Please read the oper ator’s manual carefully and make sure you understand the instr

10 – EnglishGENERAL SAFETY PRECAUTIONSCutting attachment guardThis guard is intended to prevent loose objects from being thrown towards the operator.

English – 11GENERAL SAFETY PRECAUTIONSFor mufflers it is very important that you follow the instructions on checking, maintaining and servicing your ma

12 – EnglishGENERAL SAFETY PRECAUTIONSCutting equipmentThis section describes how to choose and maintain your cutting equipment in order to:• Reduce t

English – 13GENERAL SAFETY PRECAUTIONSSharpening the saw blade• See the cutting attachment packaging for correct sharpening instructions.A correctly s

14 – EnglishASSEMBLYAssembling the handlebar and throttle (BC 2145, CC 2145)• Remove the screw at the rear of the throttle handle.• Slide the throttle

English – 15ASSEMBLYAssembling the cutting equipmentFitting the blade guard/combination guard, grass blade and ball-bearing-mounted support cup• Hang

16 – EnglishASSEMBLYFitting the blade guard and saw blade• The blade guard (A) is fitted using 4 screws (L) as shown.CAUTION! Always use the recommende

English – 17ASSEMBLYFitting other guards and cutting attachments• Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/p

18 – EnglishASSEMBLY2 Grass clearingThe machine should be supported in a harness when grass clearing so that the cutting equipment is parallel to the

English – 19FUEL HANDLINGFuel safetyNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evapor

2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

20 – EnglishFUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

English – 21STARTING AND STOPPINGCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent

22 – EnglishSTARTING AND STOPPINGStart throttle: (FC 2145, FC 2145 S, FC 2145 W, BC 2145, CC 2145)Set the throttle to the start position by moving the

English – 23WORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

24 – EnglishWORKING TECHNIQUESWorking methods• Before you start clearing, check the clearing area, the type of terrain, the slope of the ground, wheth

English – 25WORKING TECHNIQUES• To fell a tree forwards, the bottom of the tree should be pulled backwards. Pull the blade backwards with a quick, firm

26 – EnglishWORKING TECHNIQUESGrass trimming with a trimmer headTrimming• Hold the trimmer head just above the ground at an angle. It is the end of th

English – 27MAINTENANCECarburetorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engi

28 – EnglishMAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir

English – 29MAINTENANCEAdjusting the start throttle speed (BC 2145, CC 2145)The correct start throttle speed is set by means of an adjuster on the rea

English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Maintenance, replacement, or repair

30 – EnglishMAINTENANCECleaning the air filterRemove the air filter cover and take out the filter. Wash it clean in warm, soapy water.An oiled foam plast

English – 31MAINTENANCEWinter useRunning problems can occur when using the machine in the cold and snowy conditions caused by:• Too low engine tempera

32 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 33TECHNICAL DATATechnical dataNote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure lev

34 – EnglishTECHNICAL DATANote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under vari

English – 35TECHNICAL DATABC 2145Approved accessories Type Cutting attachment guard, Art. no.Centre hole in blades/cutters, Ø 25,4 mm Output shaft thr

36 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

1Poly Trim2345678<20mm>20mm!BA6 NmX 10

12345678935-50 NM~ 15 cm6'"Clic"~ 3,5 m11 '7,0 m23'2,4-3,3 mm.095"-.130"12 cm5"Trimmy SII

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

2,7-3,3 mm.106-.130"15 cm 6"15 cm 6"15 cm 6"15 cm 6"12356710111.)2.)>1,1 Kw<1,1 Kw2,7 mm - 9,0 m3,0 mm

"Clic"123567910 m32'484,3 m14'2,7-3,3 mm.106-.13"10 cm 4"6"15 cmTap n’Go 45 Spin

´®z+Rvy¶5s¨´®z+Rvy¶5s¨

´®z+Rvy¶5s¨2008-02-08´®z+Rvy¶5s¨1150868-95

English – 5 WHA T IS WHA T? What is what on the c learing saw? (BC 2145)26272863517422243393287182019214131212934342324113025131214161523353610 1

6 – English WHA T IS WHA T? What is what on the c learing saw? (FC 2145, FC 2145 S, FC 2145 W)2427252623635131112971781416152122181420181928293023

English – 7 WHA T IS WHA T? What is what on the c learing saw? (CC 2145)12326272835422243393287182019214131212934342324113025131214161523353461017

8 – English GENERAL SAFETY PRECA UTIONS Impor tantPersonal protective equipment HELMET A helmet should be w orn if the trees being cleared are tall

English – 9 GENERAL SAFETY PRECA UTIONS Mac hine ′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and ho