Jonsered CC2036 Manuel d'utilisateur

English GR2036 CC2036 Operator’ s manual (EPA) Please read the oper ator’s manual carefully and make sure you understand the instructions before u

GENERAL SAFETY PRECAUTIONS10 – Englishshould operate the socket spanner when loosening or tightening the nut.The nylon lining inside the locking nut m

GENERAL SAFETY PRECAUTIONSEnglish – 11Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.Sharpe

GENERAL SAFETY PRECAUTIONS12 – EnglishTrimmer head• Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufactur

ASSEMBLYEnglish – 13Fitting the handlebar• Remove the screw at the rear of the throttle handle.• Slide the throttle handle onto the right side of the

ASSEMBLY14 – EnglishFitting blades and trimmer headsFitting a blade guard, grass blade and grass cutter• Hook the blade guard/combination guard (A) on

ASSEMBLYEnglish – 15CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. • Fit the driv

ASSEMBLY16 – EnglishFitting other guards and cutting attachments• Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/p

ASSEMBLYEnglish – 17Correct height1 Forestry clearingAdjust the support strap so that the support hook is around 10 cm below your hip. The blade shoul

FUEL HANDLING18 – EnglishFuel safetyNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evapor

FUEL HANDLINGEnglish – 19Mixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

STARTING AND STOPPING20 – EnglishCheck before startingFor safety reasons follow these recommendations!• Check the blade to ensure that no cracks have

STARTING AND STOPPINGEnglish – 21Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled.

WORKING TECHNIQUES22 – EnglishGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

WORKING TECHNIQUESEnglish – 23The ABC of clearing• Always use the correct equipment.• Make sure the equipment is well adjusted.• Follow the safety pre

WORKING TECHNIQUES24 – Englishconditions, so that cleared stems fall in the cleared area of the stand.Forestry clearing using a saw blade• The risk of

WORKING TECHNIQUESEnglish – 25Brush cutting with a saw blade• Thin stems and brush are mown down. Work with a sawing movement, swinging sideways.• Try

WORKING TECHNIQUES26 – EnglishCutting• The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord paral

MAINTENANCEEnglish – 27CarburetorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engi

MAINTENANCE28 – EnglishLow speed jet LTry to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. Wh

MAINTENANCEEnglish – 29this screw (4 mm Allen screw) to increase or decrease the start throttle speed.Proceed as follows:1 Run the machine at idle.2 P

CONTENTS English – 3 Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Maintenance, replacement, or repai

MAINTENANCE30 – EnglishBevel gearThe bevel gear is filled with the right amount of grease at the factory. However, before using the machine you should

English – 31MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

32 – EnglishTECHNICAL DATATechnical dataNote 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure lev

English – 33TECHNICAL DATAApproved accessories Type Cutting attachment guard, Art. no.Centre hole in blades/cutters, Ø 25,4 mmOutput shaft thread M12

FEDERAL EMISSION CONTROL WARRANTY STATEMENT34 – EnglishYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

FEDERAL EMISSION CONTROL WARRANTY STATEMENTEnglish – 35EMISSION CONTROL WARRANTY PARTS LIST1 Carburetor and internal parts2 Intake pipe, airfilter hol

1Poly Trim2345678<20mm>20mm!BA6 NmX 10

Tap n’ Go 35 Spin"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm

"Clic"123567910 m32'484,3 m14'2,7-3,3 mm.106-.13"10 cm 4"6"15 cmTap n’Go 45 Spin

12345678935-50 NM~ 15 cm6'"Clic"~ 3,5 m11 '7,0 m23'2,4-3,3 mm.095"-.130"12 cm5"Trimmy SII

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

1151476-95´®z+SOe¶5q¨´®z+SOe¶5q¨2009-01-16

English – 5 WHA T IS WHA T? What is what?28222416151413231234567891017111225 262729 1 Blade2 Grease filler cap, bevel gear3 Bevel gear4 Cutting att

GENERAL SAFETY PRECA UTIONS 6 – English Impor tant Personal protective equipment HELMET A helmet should be w orn if the trees being cleared are tal

GENERAL SAFETY PRECA UTIONS English – 7 BOO TSWear boots with steel toe-caps and non-slip sole.CLOTHINGWear clothes made of a strong fabric and av

GENERAL SAFETY PRECA UTIONS 8 – English be chec ked. See instructions under the heading Maintenance. Stop s witch Use the stop s witch to switch of

GENERAL SAFETY PRECAUTIONSEnglish – 9saw. Certain harnesses also have a quick release fitted to the support hook.Check that the harness straps are corr