Jonsered CS2163 Manuel d'utilisateur

Operator´s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

10 – English SAFETY INSTRUCTIONS Some terms that describe the bar and chain When the cutting equipment supplied with your saw becomes worn or damage

English – 11 SAFETY INSTRUCTIONS 4 Round file diameter5 File depthIt is very difficult to sharpen a chain correctly without the right equipment. We re

12 – EnglishSAFETY INSTRUCTIONS• To adjust the raker clearance you will need a flat file and a raker gauge.• Place the gauge over the raker lip.• Place

English – 13SAFETY INSTRUCTIONSChecking chain lubrication• Check the chain lubrication each time you refuel. Aim the tip of the bar at a light coloure

14 – EnglishSAFETY INSTRUCTIONSBarCheck regularly:• Whether there are burrs on the edges of the bar. Remove these with a file if necessary.• Whether th

English – 15SAFETY INSTRUCTIONSDo not let go of the handles! 3 Most kickback accidents happen during limbing. Make sure you are standing firmly and tha

16 – EnglishSAFETY INSTRUCTIONS• Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manu

English – 17SAFETY INSTRUCTIONS• Never start the machine: 1 If you have spilt fuel or chain oil on the machine. Wipe off the spillage and allow remain

18 – EnglishSAFETY INSTRUCTIONS• Never put a chain saw down while the engine is running unless you have it in clear view and the chain brake is on. Sw

English – 19SAFETY INSTRUCTIONSThe log is supported at one end. There is a high risk that it will split.Start by cutting from below (about 1/3 of the

2 – English KEY TO SYMBOLS Key to symbols WARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to t

20 – EnglishSAFETY INSTRUCTIONSClearing the trunk and preparing your retreatRemove any branches that are in the way. To do this it is best to work fro

English – 21SAFETY INSTRUCTIONSWhen the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a fell

22 – EnglishWHAT IS WHAT?What is what on the chain saw?JONSERED SERVICEJonsered 2163 TURBOJonseredHuskvarna, SWEDENXXXXXXXXXXXCS2163CS2165CS21711 Cyl

English – 23ASSEMBLYFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

24 – EnglishFUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stro

English – 25FUEL HANDLINGFuellingClean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at

26 – EnglishSTARTING AND STOPPINGStarting and stoppingCold engineStarting: The chain brake must be engaged when the chain saw is started. Activate the

English – 27STARTING AND STOPPINGReactivate the chain brake by pushing the front hand guard back towards the front handle. The chain saw is now ready

28 – EnglishMAINTENANCECarburettorFunction, Basic settings, Fine adjustmentFunction• The carburettor governs the engine’s speed via the throttle contr

English – 29MAINTENANCEthrottle for about 10 seconds. Then turn the H-jet 1/4 turn anti-clockwise. Run the machine at full throttle for another 10 sec

English – 3 CONTENTS Contents Before using a new chain saw • Please read the operator’s manual carefully and make sure you understand the instructio

30 – EnglishMAINTENANCEFitting the starter•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase.

English – 31MAINTENANCEAdjustment of the oil pumpThe oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combinat

32 – EnglishMAINTENANCECAUTION! The carburettor heater reaches maximum temperature after about 3 minutes. It is therefore important that the machine i

English – 33TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/

34 – EnglishTECHNICAL DATA´®z*xy^¶6}¨´®z*xy^¶6}¨Bar and chain combinationsThe following combinations are CE approved.Bar ChainLength, inches Pitch, in

English – 35TECHNICAL DATAEC-declaration of conformity(Applies to Europe only)Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares unde

´®z*xy^¶6}¨2004-04-15´®z*xy^¶6}¨1088896-26

4 – English SAFETY INSTRUCTIONS Personal protective equipment • Protective helmet• Hearing protection• Protective goggles or a visor• Gloves with sa

English – 5 SAFETY INSTRUCTIONS Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain im

6 – English SAFETY INSTRUCTIONS Throttle lock The throttle lock is designed to prevent accidental operation of the throttle control. When you press

English – 7 SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′′′′ s safety equipment Chain brake and front hand guard Checking b

8 – English SAFETY INSTRUCTIONS Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released.• Pr

English – 9 SAFETY INSTRUCTIONS Never use a muffler if the spark arrestor mesh is missing or defective. Cutting equipment This section describes how