Jonsered CS 2153 Manuel d'utilisateur

English CS 2152 CS 2153 Operator ′′′′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before u

GENERAL SAFETY PRECAUTIONS10 – EnglishThe machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipme

GENERAL SAFETY PRECAUTIONSEnglish – 11• Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased

GENERAL SAFETY PRECAUTIONS12 – English• Number of drive links.Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening

GENERAL SAFETY PRECAUTIONSEnglish – 13General advice on adjusting depth gauge setting• When you sharpen the cutting tooth (A) the depth gauge setting

GENERAL SAFETY PRECAUTIONS14 – EnglishLubricating cutting equipmentChain oilChain oil must demonstrate good adhesion to the chain and also maintain it

GENERAL SAFETY PRECAUTIONSEnglish – 15Needle bearing lubricationBoth versions of sprockets have a needle bearing on the drive shaft, which has to be g

ASSEMBLY16 – EnglishFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

FUEL HANDLINGEnglish – 17FuelNote! The machine is equipped with a two-stroke engine and must always be run using a mixture of petrol and two-stroke oi

FUEL HANDLING18 – EnglishFuellingClean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at

STARTING AND STOPPINGEnglish – 19Starting and stoppingCold engineStarting: The chain brake must be engaged when the chain saw is started. Activate the

KEY T O SYMBOLS 2 – English Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fat

STARTING AND STOPPING20 – EnglishAs the chain brake is still engaged the speed of the engine must be set to idling as soon as possible, this is achiev

WORKING TECHNIQUESEnglish – 21Before use:1 Check that the chain brake works correctly and is not damaged.2 Check that the rear right hand guard is not

WORKING TECHNIQUES22 – English6 Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with

WORKING TECHNIQUESEnglish – 237 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is

WORKING TECHNIQUES24 – EnglishThe following instructions describe how to handle the commonest situations you are likely to encounter when using a chai

WORKING TECHNIQUESEnglish – 25Finish by cutting from below so that the two cuts meet.Tree felling techniqueSafe distanceThe safe distance between a tr

WORKING TECHNIQUES26 – EnglishFellingFelling is done using three cuts. First you make the directional cuts, which consist of the top cut and the botto

WORKING TECHNIQUESEnglish – 27All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional

WORKING TECHNIQUES28 – EnglishGeneral advice:Position yourself so that you will be clear of the tree or branch when the tension is released.Make one o

MAINTENANCEEnglish – 29GeneralThe user must only carry out the maintenance and service work described in this manual.Carburettor adjustmentDue to exis

CONTENTS English – 3 Contents KEY TO SYMBOLS Symbols on the machine: ... 2Symbols in the operator’s manual: .

MAINTENANCE30 – EnglishHigh speed jet HAt the factory the engine is adjusted at sea level. When working at a high altitude or in different weather con

MAINTENANCEEnglish – 31Checking the inertia brake releasePlace the chain saw, with the engine switched off, on a stump or other stable surface. Releas

MAINTENANCE32 – EnglishRight hand guardCheck that the right hand guard is not damaged and that there are no visible defects, such as cracks.Vibration

MAINTENANCEEnglish – 33StarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta

MAINTENANCE34 – EnglishFitting the starter• To fit the starter, first pull out the starter cord and place the starter in position against the crankcase.

MAINTENANCEEnglish – 35Needle bearing lubricationThe clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regu

MAINTENANCE36 – EnglishWinter useRunning problems can occur when using the machine in the cold and snowy conditions caused by:• Too low engine tempera

English – 37MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

38 – EnglishTECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/

English – 39TECHNICAL DATABar and chain combinationsThe following recommended combinations of bar and saw chain are type approved for your chain saw.

4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to buy a Jonsered product!We are convinced that you will appreciate with

40 – EnglishTECHNICAL DATAEC-declaration of conformity(Applies to Europe only)Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares unde

1151207-26´®z+S4h¶6k¨´®z+S4h¶6k¨2008-07-08

English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Cylinder cover2 Front handle (Felling direction guide)3 Front hand guard4 Starter5 C

GENERAL SAFETY PRECA UTIONS 6 – English Bef ore using a new chain saw • Please read this manual carefully.• Check that the cutting equipment is cor

GENERAL SAFETY PRECA UTIONS English – 7 pro vide information about which training materials and courses are available. Work is constantly in progr

GENERAL SAFETY PRECAUTIONS8 – English• The brake is applied when the front hand guard (B) is pushed forwards.• This movement activates a spring-loade

GENERAL SAFETY PRECAUTIONSEnglish – 9• In the felling position the left hand is in a position that makes manual activation of the chain brake impossib