Jonsered 2141 Manuel d'utilisateur

Operator's manualPlease read these instructions carefullyand make sure you understand thembefore using the machine.

10 – English7 MufflerNever use a chain sawthat has a faulty muffler.Regularly check that themuffler is securelyattached to the chain saw.If the muffle

English – 11SAFETY INSTRUCTIONSC Some terms that describe the bar and chainWhen the cutting equipment supplied with your saw becomesworn or damaged yo

12 – EnglishSAFETY INSTRUCTIONS2 Sharpening your chain and adjustingraker clearanceThe risk of kickback is increased with a badlysharpened chain!A Gen

English – 13C General advice on setting raker clearance• When you sharpen thecutting teeth you reduce theRAKER CLEARANCE(cutting depth). To maintaincu

14 – English1 Undo the bar nuts thathold the clutch cover andchain brake, using thecombination spanner.Then tighten the nuts byhand as tight as you ca

English – 15C Checking chain lubrication• Check the chain lubricationeach time you refuel.Aim the tip of the saw at alight coloured surface about20 cm

16 – EnglishH BarCheck regularly:• Whether there are burrs onthe edges of the bar.Remove these with a file ifnecessary.• Whether the groove in thebar

English – 177 Take great care when youcut with the top edge ofthe bar, i.e. when cuttingfrom the underside of theobject. This is known ascutting on th

18 – EnglishSAFETY INSTRUCTIONSGENERAL SAFETY PRECAUTIONS1 Chain saws are designed solely for cutting wood. The onlycutting equipment that can be used

English – 19SAFETY INSTRUCTIONSMin. 3 m(10 ft)• Never try to refuel the sawwhile it is running.• Make sure there is plenty ofventilation when refuelli

2 – EnglishKEY TO SYMBOLSOther symbols/decals on the machine refer to specialcertification requirements for certain markets.This product is fitted wit

20 – EnglishSAFETY INSTRUCTIONS6 Before moving your chainsaw switch off the engineand lock the chain usingthe chain brake. Carry thesaw with the bar a

English – 21SAFETY INSTRUCTIONS2 The log is supported at oneend. There is a high riskthat it will split.A Start by cutting frombelow (about 1/3 of the

22 – EnglishSAFETY INSTRUCTIONSC Clearing the trunk and preparing your retreatRemove any branches thatare in the way. To do this it isbest to work fro

English – 23We recommend that you usea bar that is longer than thediameter of the tree, so thatyou can make the FELLINGCUT and DIRECTIONAL CUTwith sin

24 – EnglishWHAT IS WHAT?1. Cylinder cover.2. Front handle.3. Front hand guard.4. Starter cover.5. Chain oil tank.6. Starter handle.7. Adjuster screw,

English – 25ASSEMBLYFitting a spike bumperTo fit a spike bumper –contact your service agent.Hold up the tip of the bar andtighten the chain. The chain

26 – EnglishMixing• Always mix the petrol andoil in a clean containerintended for fuel.• Always start by filling halfthe amount of the petrol tobe use

English – 27FUEL HANDLINGFuellingTaking the following precautions, will lessenthe risk of fire.• Do not smoke or place warm objects in the vicinity of

28 – EnglishStartGrip the front handle with yourleft hand and hold the sawdown by putting your right footin the rear handle. Pull thestarter handle wi

English – 29!CarburettorFunctioning, Basic setting, Final settingWARNING! Do not start the saw without the bar,chain and clutch cover (chain brake) as

English – 3CONTENTSContentsKey to symbols... 2Safety instructionsPersonal protective equip

30 – EnglishStarter deviceWARNING!• When the recoil spring is assembled in the starterhousing, it is in tensioned position and can whentreated careles

English – 31MufflerThe muffler is designed inorder to reduce the noise leveland to direct the exhaustgases away from the operator.The exhaust gases ar

32 – EnglishMAINTENANCECooling systemTo obtain the lowest possible running temperature the saw isequipped with a cooling system.The cooling systemcons

English – 33Below you will find some general maintenance instructions.If you have more questions, contact your servicing dealer.Weekly maintenance1. C

34 – EnglishEngineCylinder volume, cu.in/cm3Cylinder bore, inch/mmStroke, inch/mmIdle speed, rpmRecommended max. speed, unloaded, rpmPower, kW/ rpmIgn

English – 35TECHNICAL DATABar and chain combinationsThe following combinations are CE approved.Bar ChainLength, Pitch, Max.inches inches tip radius13

2002W01´*xsT¶6I¨108 88 35-26

4 – EnglishSAFETY INSTRUCTIONS• PROTECTIVE HELMET• HEARING PROTECTION• PROTECTIVE GLASSESOR VISOR• PROTECTIVE GLOVESWITH SAW PROTECTION• PROTECTIVE TR

English – 51 Chain brake and front hand guardYOUR chain saw is equipped with a chain brake that is desig-ned to stop the chain immediately if you get

6 – English6 The way the chain brake is triggered, either manually orautomatically, depends on the force of the kickback and theposition of the chain

English – 75 Vibration damping systemYour chain saw is equippedwith a vibration dampingsystem that is designed tominimise vibrations and makeoperation

8 – EnglishSAFETY INSTRUCTIONS3 Checking the inertia brake releaseHold the chain saw over astump or other firm object.Let go of the front handleso tha

English – 9SAFETY INSTRUCTIONS4 Right hand guardCheck that the right handguard is not damaged andthat there are no visibledefects, such as cracks.5 Vi